Discovering Essential Plumbing Skills is Important For Installing a Bathtub
Discovering Essential Plumbing Skills is Important For Installing a Bathtub
Blog Article
How do you actually feel on the subject of Installing A Bathtub?
Mounting a tub isn't exactly rocket science, however it does require solid plumbing, carpentry, as well as in some cases, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately tough job. If the old bathtub is easily available, the task can relocate easily; if you have to open a wall surface to eliminate the old tub and place the new tub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will require an assistant to vacate the old tub and embeded in the new one. Ensure you have certified on your own for the work and also are comfortable trying it. Instead of employing a service provider to take over a halfway-completed project, it is better to consider using one prior to you start. Opportunities are you may need a professional plumber to make tube connections.
This write-up will assist you install a brand-new bath tub in your bathroom if you have actually currently acquired a new bathtub and do not need to change the setup of your previous water system pipes.
Your devices and material list need to make up the following:
Getting ready for the Setup
First of all, the supporting frame supplied with the bathroom must be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps unit to stop strain on the bath tub.
Fit the versatile faucet connectors to the bottom of both faucets using 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must now be ready to be suited its final setting.
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, after that the first thing you need to do is separate the supply of water. After doing so, activate the faucets to drain any type of water staying in the system. The process of getting rid of the existing faucets can be fairly bothersome as a result of the limited gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a towel all set for the remaining water that will certainly come from the pipelines. As soon as the supply pipelines have been eliminated, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from transforming during this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Before proceeding to fit the new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Making use of the two wooden boards under its feet, place the tub in the needed setting. The wood boards are helpful in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by checking the spirit level and changing the feet on the bath tub till the level reads degree.
To set up faucets, fit all-time low of the furthest flexible faucet adapter to the proper supply pipe by making a compression join; after that do the exact same for the various other faucet.
Switch on the water supply and inspect all joints as well as new pipework for leakages and also tighten them if required. Fill up the bathtub and also examine the overflow outlet as well as the normal electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the maker's user's manual. Tiling as well as securing around the tub must wait till the tub has been made use of at the very least once as this will certainly settle it right into its final placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the other end gives a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the mounting hole in the bath/basin making certain that the washers are in place in between the tap and also the sink. Safeguard the faucet in position with the supplier supplied backnut. When the tap is securely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical tap ports. The former kind ought to be connected to the tap finishes first, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a rigid seal, creating the water to pass through the wall in between the bath and also the tiling, resulting in issues with wetness and feasible leaks to the ceiling below.
You can pick from a range of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes and cartridges, and are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill the bathtub with water prior to sealing, to enable the activity experienced when the bathtub remains in use. The sealant can fracture relatively early if you do not consider this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or waterproof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed reading our excerpt about A Step-by-Step Guide to Installing a Bathtub. Thank you so much for spending some time to browse our blog post. Be sure to take the time to share this entry if you enjoyed it. We truly appreciate reading our article about Tools You Need to Install a New Bathtub .
Schedule Free Estimate Report this page